| E-Z KUT Hunting Products Tree Drilling Instructions |
Drilling Instructions
E-Z KUT Hunting Products Convertible Hand Drill and Cordless Drill Bit is engineered for years of service
with normal use and care. The drill bit is manufactured to just the right size (diameter) to give clearance for
the 6” E-Z UP Step Bolts.
Here’s how to drill a tree with the hand drill:
1. Place the heel of your left hand against the tree and grasp the hand drill by its collar with your thumb
underneath and your first and middle fingers on top of the collar.
2. Angle the drill bit down slightly; this will prevent the Step-Bolts from falling out.
3. Exert just enough inward pressure to start the drill; the drill bit is self-feeding and requires no inward
pressure while drilling the hole. Don’t try changing the angle that the bit is cutting at while it is cutting; the
self-feeding tip is very hard and may break off. If you’re not happy with the angle or placement remove the
bit and start over at a different location.
4. When the bit reaches the proper depth it will stop drilling at that point you will feel the last wood chip
break; continue turning the drill a few more times then grasp the drill by the handle with the bit between
your first and middle fingers and pull the bit straight out; there is no need to turn the drill backwards.
Pulling the bit out will pull out the wood chips.
5. As you are ascending the tree just leave the hand drill and bit in the last highest hole to free up both
hands so you can raise your safety belt then step up to a higher Step-Bolt.
6. Slide in your E-Z UP Step-Bolts.
Here’s how you use the Convertible Cordless Drill Bit:
1. Place the drill bit in the chuck of your cordless drill. Angle the bit downward slightly and exert slight
inward pressure to start the bit cutting. Then just support the drill so the bit does not bind; the bit is self-
feeding and will pull itself into the tree that you are drilling.
2. When the bit stops cutting just run the drill for a few seconds while pulling the drill bit out of the tree.
Flick out the chips from the bit flutes before starting another hole.
3. As you are ascending the tree just leave the drill and bit in the last highest hole to free up both hands so
you can raise your safety belt and step up higher on the Step-Bolts.
4. Slide in your E-Z UP Step-Bolts as you go up.
E-Z KUT Hunting Products
2118 Plum Grove Rd. Suite 355, Rolling Meadows, Illinois 60008
(847) 253-8537
www.ezkutpruners.com
HOME
Site Map
E-Z KUT Hunting Products Convertible Hand Drill and Cordless Drill Bit is engineered for years of service
with normal use and care. The drill bit is manufactured to just the right size (diameter) to give clearance for
the 6” E-Z UP Step Bolts.
Here’s how to drill a tree with the hand drill:
1. Place the heel of your left hand against the tree and grasp the hand drill by its collar with your thumb
underneath and your first and middle fingers on top of the collar.
2. Angle the drill bit down slightly; this will prevent the Step-Bolts from falling out.
3. Exert just enough inward pressure to start the drill; the drill bit is self-feeding and requires no inward
pressure while drilling the hole. Don’t try changing the angle that the bit is cutting at while it is cutting; the
self-feeding tip is very hard and may break off. If you’re not happy with the angle or placement remove the
bit and start over at a different location.
4. When the bit reaches the proper depth it will stop drilling at that point you will feel the last wood chip
break; continue turning the drill a few more times then grasp the drill by the handle with the bit between
your first and middle fingers and pull the bit straight out; there is no need to turn the drill backwards.
Pulling the bit out will pull out the wood chips.
5. As you are ascending the tree just leave the hand drill and bit in the last highest hole to free up both
hands so you can raise your safety belt then step up to a higher Step-Bolt.
6. Slide in your E-Z UP Step-Bolts.
Here’s how you use the Convertible Cordless Drill Bit:
1. Place the drill bit in the chuck of your cordless drill. Angle the bit downward slightly and exert slight
inward pressure to start the bit cutting. Then just support the drill so the bit does not bind; the bit is self-
feeding and will pull itself into the tree that you are drilling.
2. When the bit stops cutting just run the drill for a few seconds while pulling the drill bit out of the tree.
Flick out the chips from the bit flutes before starting another hole.
3. As you are ascending the tree just leave the drill and bit in the last highest hole to free up both hands so
you can raise your safety belt and step up higher on the Step-Bolts.
4. Slide in your E-Z UP Step-Bolts as you go up.
E-Z KUT Hunting Products
2118 Plum Grove Rd. Suite 355, Rolling Meadows, Illinois 60008
(847) 253-8537
www.ezkutpruners.com
HOME
Site Map